AUDI – VW key programming OBD2 – NEW / BLUE / DEVICE

 


 AUDI, VW, SKODA, SEAT 348 key programmer ITV2

 

AUDI A4,S4,RS4,A5,S5,RS5,SQ5      2008-04/2014 

LAMBORGHINI AVENTADOR  2011-04/2014

LAMBORGHINI GALLARDO    2003-2013

VW TOUAREG – 2010-04/2014

VW,SEAT,SKODA – 2008-02/2012

AUDI A1,A3 – 2010-10/2012

AUDI A4 – 2001-2007

The only device in Europe for programming keys for the latest Audi models.

Programs new keys through OBD2.

The device is tested on all models.

Special function – in case of emergency turns off the alarm through OBD2. 

New programming function keys for the A4,A5,Q5 2013-2014 cars.

New programming function keys for the A8 after changing software in service.

Additional programs for programming keys for older models of Audi,VW.


 AUDI BCM 2 2007-2013 – 1

  • Audi
    • A4 (B8) Typ 8K 2008+
    • A5 2007+
    • S5 (B8) 2009+
    • RS5 2010+
    • RS4 2010-2012
    • RS6
    • Q5 2007+
    • A6 (C7) Typ 4K 2010+
    • A7 Sportback 2010+
    • A8 (D4) Typ 4H 2010+
    • R8 up to 2011
  • VW Touareg Typ 7P5 2010+ 

The BCM2 key learning device is dedicated to programming keys for vehicles equipped with BCM2 module.

The key learning device is equipped with a key programmer, which allows to pre-code the blank keys. 
The device has the following modes of operation:
*Program 1 to 8 keys to the car

Check whether the key is blank

Switch the alarm OFF

Our device needs 25 seconds to learn a key, it also supports BCM2 modules:

xx0907064xx, 8K0907289C.

HOW TO USE:

1 BCM2 Key learning device.

The BCM2 key learning device is dedicated to programming keys for vehicles equipped with BCM2 module. These are the models of Audi A4/A5/S5/Q5 2007+, Audi A6 2010+, Audi A8 2010+, Audi A7 2010+, VW Touareg 2010+.

The key learning device has a key programmer, which allows to pre-code the blank keys.

The device has the following modes of operation:

Program 1 to 8 keys to the car

Check whether the key is blank

Switch the alarm OFF because in “all keys lost” situation the alarm will be working

Switch the alarm ON if it was previously turned OFF due to “all keys lost” situation

2 Key learning procedures

You should specify the number of keys you want to learn using the SW1, SW2, SW3. In the table below you can find how the number of keys is specified:

  SW1 SW2 SW3
1 key OFF OFF OFF
2 key OFF OFF ON
3 key OFF ON OFF
4 key OFF ON ON
5 key ON OFF OFF
6 key ON OFF ON
7 key ON ON OFF
8 key ON ON ON

Perform the procedure by following these steps:

1. Specify the number of keys that you want to learn.

2. Give ignition ON with a working key. If all keys are lost, turn on the radio, and switch the lights ON. If you don’t have a working key and you don’t turn on the lights and the radio, there will be no communication with the car and that is why the procedure will fail.

3. Put the device into the OBDII, it starts to communicate, and the LED starts blinking.

4. In “all keys lost” situation after 5-6 seconds the LED will be constantly RED. In this situation you should go to the trunk, find the BCM module and disconnect both of the 17-PIN connectors (black and brown). After 2-3 seconds reconnect these connectors again. If you made ignition ON with a working key, skip this step.

5. After 15-20 seconds the LED will be constantly GREEN and then you will see information on the dashboard showing that the learning procedure is active. If you have specified to learn e.g. 3 keys, you will see on the display “0/3”. At this moment you should give ignition ON with each key you want to learn. If the car is key-less-go, place the key near the vehicle coil instead of inserting it into the ignition lock. After giving ignition with each key, the dashboard indication will change “1/3”, 2/3” and so on until the end value (“3/3” in this case). Then the procedure will finish indicating success.

If you want to learn a blank key, before giving ignition ON with it, you should put it in the ring coil. The LED will start to blink GREEN indicating that a key is detected and is currently pre-coded. After pre-coding the key successfully, the LED will be constantly GREEN again, and then you can give ignition ON with this key to learn it.

At this moment you can pre-code in that way as many keys as you want using this procedure. If the key cannot be pre-coded for any reason (e.g. because the key is not blank, or if you remove it from the coil before the pre-coding has finished) the LED will become RED for three seconds, and after that again constantly GREEN awaiting to pre-code next blank key.

NOTE: In some cases, we recommend to make the lights cyclically ON/OFF each 2-3 seconds when the LED is blinking. So, if the procedure fails, repeat it making the lights ON/OFF during the procedure.

 Checking whether the key is blank

Make SW6 to ON position and put the device in any OBDII socket (this procedure can be also executed on another vehicle). The LED should be constantly GREEN. Put the key that you want to check whether is blank. After that the LED starts to blink GREEN while checking the key. When the check finishes the indication is as follows:

Success indication – the key is blank (LED blinks GREEN slowly)

Error indication – the key is not blank (LED blinks RED fast)

Switching the alarm OFF

This mode of operation is necessary only when all keys are lost. After unlocking the door the alarm will be triggered in 15 seconds. Make SW8 to ON, all others to OFF. Turn on the radio, and switch the lights ON, then put the device into the OBDII. After 4-5 seconds the device will indicate success (LED blinks GREEN slowly) which means that the alarm is already OFF. At this moment you can unlock the door once again, which will unlock all doors and give you access to the trunk where the BCM2 module is located – you will need that for the key learning procedure.

Switching the alarm ON

This mode of operation is necessary only when all keys are lost and you have disabled the alarm. After finishing the key learning procedure you should restore the alarm. Make SW7 to ON, all others to OFF. Turn on the radio, and switch the lights ON, then put the device into the OBDII. After 4-5 seconds the device will indicate success (LED blinks GREEN slowly) so the alarm is already ON.

Indications

The following indications show the final result on the device:

Success indication: After having finished with success the LED is blinking slowly GREEN.

Error indication: In case of any error the LED is blinking RED fast.

Supported BCM2 modules:

Supported BCM2 modules are xx0907064xx, 8K0907289C.

Examples:

All keys are lost and you want to make 1 key

Switch the alarm OFF using the procedure described in 4).

Make SW8 to ON, all others to OFF.

Then unlock the driver’s door.

After that put the device into the OBDII and wait for success indication.

Unlock the driver’s door once again to unlock all doors and the trunk.

Learn 1 key

Eject the device from the OBDII, then make all switches to OFF ( this actually specifies that 1 key will be learned ).

Turn on the radio and switch on the lights.

After that put the device into the OBDII again.

Wait until the LED is constantly RED, then disconnect both 17-PIN connectors from BCM2 and after 2-3 seconds reconnect them again.

Wait until the LED is constantly GREEN, dashboard will show “0/1” and then put the blank key in the device ring coil.

LED starts to blink GREEN, wait until it is again constantly GREEN.

Give ignition ON with this key. If the car is key-less-go, place the key near the vehicle coil.

Then the dashboard indication should change from “0/1” to “1/1”.

After that you can start the car.

Switch alarm ON

Eject the device from the OBDII, then make SW7 to ON, all other switches to OFF.

Put the device into the OBDII and then wait for the success indication.

The car has 1 key and you want to add 1 key

Learn 2 keys.

Make SW3 to ON, all others to OFF (this actually specifies that 2 keys will be learned).

Then make ignition ON with the working key.

Afterwards put the device into the OBDII.

Wait until the LED is constantly GREEN, the dashboard will indicate “0/2”.

If the working key is in the ignition, the dashboard will change to “1/2”. If the key is key-less-go, place the working key near the vehicle coil, and then the dashboard will change to “1/2”.

After that put the blank key in the device ring coil.

LED starts to blink GREEN, wait until it is again constantly GREEN.

Give ignition ON with this key. If the car is key-less-go, place the key near the vehicle coil.

Then the dashboard indication should change from “1/2” to “2/2”.

After that you can start the car.