Turbodecoder SIP22 full info – manual, instructions, sale

turbodecoder sip 22 mechanical elements

  • key profile – on this prodecoder tool it is SIP22 / Silca identification code / and it is made to fit in any lock of FIAT, IVECO, LANCIA, ALFA-ROMEO and MASERATI automobiles
  • sliding pins – sliding mechanical components necessary to unlock and decode the locks mounted on those Italian cars
  • pin bar – on each side of the decoder we have mounted pin bars for inserting the instrument in and extracting it out of the locks
  • tension wheel – round front segment of the turbo decoder handle to use for applying tension forces / left & right /
  • pin activator wheel – it is connected with the pin bars to command them in open or closed positions
  • turbo wheel – the back wheel of the tool handle which does rotational movements and puts in action the pins during the opening procedures.

Opening procedure and important tips to follow:

Clean the lock with some light oil spray such as WD40 to remove all the dirt accumulated over the time.

To discover the lock orientation you need to use your turbo-decoder instrument. Insert it after the turbo wheel was rotated to the right and the pin activator wheel is pushed all to the front! Hold the decoder on the ring of the pin activator wheel and insert it carefully into the lock. It is not necessary to force strong the tool, it will enter if the lock is in good mechanical condition. Now pull back only the pin activator wheel and apply rotational force on the tension wheel to the left. In this moment start to rotate the turbo wheel to the left too and feel the rotation, it will be easy with no resistance and in some point you will feel a resistance on it. Note where its line points to in the moment when the resistance begins. IF the line of the turbo wheel is before the first stop sector – your orientation is good and you can start the opening procedure. If that line is after the first stop sector please turn the turbo wheel all to the right, push to the front the activator wheel and extract the decoder from the lock, reverse it and insert again. Now your tool is orientated correctly.

To open the lock please pull back the pin activator wheel, force the tension tool to the right and rotate the turbo wheel to the left till its line reaches to the first stop sector. Turn back the turbo wheel to its initial position – all to the right. Loose the tension force on the tension wheel and check the lock. Now apply force to the left on the tension wheel and repeat the rotation with the turbo wheel up to stop sector 1. Go back with it and loose the tension. Repeat these steps 20 times.

Turbodecoder sip22 open proedure

If the lock is not open please increase the rotating of the turbo wheel to the second stop point. All the rest is the same. Just the stop point is changed from 1 to 2.

prodecoder opening procedure

Do the same 20 more times and if there is no result – do it all again but stop at sector 3 for 20 more times.

turbodecoder sip22 stop point 3

Decoding of FIAT / IVECO  locks opened with TurboDecoder SIP22

If you need to decode the lock you just opened with your tool please follow the instructions:

Once your tool turns the lock and it can be opened please do not remove it. Keep the lock turned to left or right but not in neutral position. When you are in turned position please rotate the turbo wheel all to the left / its line will point at stop sector 3 /. Leave it there and jiggle the tool by following the plane of the key profile. Then turn the turbo wheel all to the right, rotate the tool to neutral lock position, push forward the pin activator wheel and extract the tool from the lock.

With the Turbodecoder out of the lock please pull back the pin activator wheel / pins become visible / and rotate the back wheel up to sector 3. 

Now see the pins, calculate the pin depths and by following the side A and side B order write down the discovered code. This is the mechanical code needed to cut a working mechanical key by inserting the code in a CNC locksmith machine.

EXAMPLE OF CODE READING:

turbo decoder sip code read side a

SIDE A READING CODE – BCBD

CODE DEADING TURBODECODER SIP22 SIDE B

SIDE B READING CODE – CBAC

THE LOCK CODE IS: BCCBBADC

After the code reading you have to reset your sliding pins. This is necessary if you want to open another lock with your tool. Resetting procedure can be made ONLY WITH THIS SET UP DEVICE SIP22!!!

Correct steps to follow:

Push the pin activator wheel to the front, rotate the turbo wheel all to the right and then inject the calibrated needle part of your set up device into the hole which is located under each pin on the edge of your key profile. There are 5 holes on each. When you inject and push the resetting device, the point of its needle will slide the pin and will stop automatically when the pin arrives to its start position. Now your prodecoder tool is ready to open another SIP22 lock.

  • ATTENTION – SOME LOCKS OF THOSE VEHICLES CONTAIN 7 INSTEAD OF 8 DISCS!

SIP22 LOCK MODELS

Here the left lock has 8 wafers, the right one – 7 wafers, please note that the 7 disc lock affects your orientation procedure! Check this video to figure out what to do.

VIDEO INSTRUCTIONS TURBODECODER SIP22